1/350 Scorpene class diesel/electric submarine 2 x propeller set OKB Grigorov

Description: I will combine shipping! Add all the items you are interested into your cart and then request the total from me. With this purchase you will receive: 2 x Scorpene class diesel/electric submarine replacement screws These are CAD designed and 3D printed replacement screws for the OKB Grigorov Scorpene kit's photo-etch propellers. The screw that comes with OKB's new Scorpene kit isn't bad. But I can't imagine assembling it. The screw boss is half the size of a grain of rice, and then you're supposed to arrange the photo-etch blades after somehow attaching it (see images of that original kit's content. These are shown for comparison only)? Sure, some modelers will be able to handle it and do a good job, but I'm at that age where I take one look at that and I'm like, "F'ing nope!" Hence this offering. I've not been able to offer any kind of technical enhancement; as far as I could find there are no images available of the Scorpene's screw in public sources. So this effective matches what OKB has done, but is in a pre-assembled form. I don't expect to sell many of these of course, this is more for me, and I suspect I'll end up doing this to the Gal and Enricho Toti kits I have in my stash at some point as they suffer the same issues. Instructions on how to remove the screw from the sprue:Given the thin section of the screw blades, some care will need to be taken when removing the screw from the sprue. The resin is by nature brittle, but the sprue is thinnest where it attaches to the screw blade as it attaches at a point, by design. The best practice is to place your flush cut pliers flush up against the bottom of the screw blade, at the point where the sprue attaches, and trim there. Do not trim from the bottom, larger diameter end of the sprue. I've found that the shock of shearing the larger diameter sprue at the bottom can ping the propeller blades right off the screw boss. Work outboard to inboard, that is, trim the outboard sprues first, and then the inboard. As the outboard sprues can obscure the inboard ones, after I've detached it from the screw blade, I then trim it off the base to allow access to the sprues deeper in. Patience and care needs to be taken. Once trimmed, you'll often have a small residual sprue-nub on each propeller blade. I then use a very narrow sanding stick to carefully sand the nub down (I use the flexible/soft and narrow sanding sticks that can be purchased at just about any Hobby Lobby in the U.S.). Why do I sell 2 units as the minimum quantity? Because ultimately the material is brittle and if care is not taken then you can break the parts. Now, this resin is toughened for sure and I've been pleasantly surprised at how much battering (ooops, dropped it on the floor, ooops, slipped) it can take. But it isn't necessarily about the material as many are familiar with resin kits and this is little different. It's more about how thin these sections have been printed. And as modeling is about enjoyment, I'd hate for someone to purchase these as 1 unit and immediately break the parts and be back to square one. I think having 2 available at least gives you a much better shot. And if you only need 1, share the other with a friend! I will combine shipping. Add all the items you are interested into your cart and then request the total from me. Other 1/350 scale submarine items of interest can be found here, from full kits to detail and upgrade sets on Shapeways'dot'com/shops/mulsannescorner1/350 1/400 HobbyBoss Hobby Boss Mikro-Mir OKB Grigorov AFV Club Blue Ridge Models Combat Sub Torpedo Models Aoshima Blue Water Navy Combrig Revell Flagman Dragon Zvezda Cyber Hobby DML Fujimi Riich Iron Shipwrights Alanger L'Arsenal Tamiya Tom's Modelworks Hasegawa Italeri Wolfpack Admiralty Model Works Commander Models OzMods Polar Bear Robin

Price: 4.99 USD

Location: Charlotte, North Carolina

End Time: 2024-11-20T20:57:39.000Z

Shipping Cost: N/A USD