Audio Sensing Foil Tape Open Reel 26 FT Real Aluminum Studio Grade™ by TME

Description: TME® REAL ALUMINUM SENSING FOIL FOR 1/4" OPEN REEL TAPE 26 FOOT ROLL "Finally, sensing foil that actually works! I love this stuff!" -AS, Henderson Nevada Temporarily Sold Out, but more is on the way! ETA April 27 2024 Product Description: Professional Studio Grade™ Highly Conductive Aluminum Sensing Foil (Not Inferior "Aluminized Painted Plastic")7/32" x 26' long on 3" Easy Handle plastic core Important: Cut to the length you need for your deck's sensitivity and operating speed Custom made in Europe to exacting TME specifications in an ISO 9001 Certified Facility to ASTM D1000 Certification Large 3" Professional Core for Easier Handling and Far Less Curling Long Lasting and Clean Electrically Conductive Adhesion will not OOZE in time like other productsAlso available as pre-cut tabs on a EZ to peel off rolls of 30 or 60 Tabs TME Professional open reel deck sensing foil is custom made to TME specs in Europe specifically for open reel tape sensing. It is real, highly conductive soft aluminum foil with a non-oozing electrically conductive aerospace adhesive. Almost every other foil we see being sold as open reel sensing foil is "vapor evaporated aluminized plastic" hobby tape which is plastic coated with aluminized paint to make it shiny. That tape is fine for arts and crafts, but they do not have the conductive qualities of real foil, and from our customer's experiences, will wear out, may not work at all on some decks, and will ooze adhesive, contaminating your deck and precious tapes. Also, those hobby tapes generally are .25" wide or more which will make it nearly impossible to add to sensing to your tapes without having some of it overlap the edge of the tape which will goo up your heads and guides which is definitely not recommended. The foil's adhesive is electrically conductive, allowing you to layer cut pieces if needed, and it can be used to drain static electricity from sensitive components to ground. Sensing foil is used on any audio tape deck using foil for auto reverse and/or auto stop sensing like some TEAC models. Note: No, it will not *turn* your deck into a reversing or auto-stop deck if it's not designed to do those functions! (We had to say that.) TME ACFOIL-26 comes 26 feet on a roll with a 3" diameter plastic core. The foil has backing release paper which you remove the foil from before you adhere your new tab to the tape. We chose to use the backing release paper rather than having the foil stick to itself on the roll to keep the foil surface as clean as possible. This also allows for neat, angled cuts or butt cuts with a splicing block before application. Each roll should have enough foil for one end of around 260 tapes or more. To use: Cut about 1" or so (depending on your deck's sensitivity), center and apply the foil to the surface of the tape where your sensors are. Smooth down with a cotton tipped applicator. Sensing foil is almost always applied to the side of the tape away from the heads and NOT the oxide side. Check your manual. There should be a slight gap between the edge of the foil and the edge of the tape if centered properly but it doesn't have to be perfectly centered. Specifications Per ASTM: Foil Thickness: 1.5 Mil Total Thickness: 2.10 Mil Tensile Strength: 14 Lb/In Electrical Resistance: <0.005 Ohms per Mil Spec OTHER USES: Great for draining static away from electrical components to ground with its electrically conductive adhesive! US Recording Media, LLC is the leading source for professional post production supplies in the country servicing the best studios and the leading government, university, and private archives as well as the home recordist wanting the very best quality. TME®, Studio Grade™, VNC-4™, VNC-8™, CL-100™, RC-5™, VCFB™, Studio Grade™ and Feedpack™ are trademarks of US Recording Media, LCC. All Rights Reserved.

Price: 19.98 USD

Location: Palmerton, Pennsylvania

End Time: 2024-08-19T00:07:14.000Z

Shipping Cost: 2 USD