Audiovox Prestige Car APS95BT2 2-Button Code Learning Transmitter FCC ID ELVAT5C

Description: 800x600 800x600 Stock #: 556 (stock photo – Some case scuffs & no cracks) Shipper/Relister: 1) These remotes are completely interchangeable with stock # 554 however; these remotes are slightly smaller than remotes in stock # 554. Stock photo Some case scuffs & no cracks See pictures for an example of what you will receive One (1) Aftermarket remote keyless entry fob alarm Transmitter control clicker keyfob controller replacement Functions at 100% Tested & Guaranteed Prestige / Pursuit / Audiovox / Pro 800x600 Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 Frequency: 302 - 309 MHz LED color: Red 2 buttons Battery: (1) 23A Compatible with the following systems: APS100 APS150 APS150A APS175 APS200 APS25KB APS250 APS250A APS25CLVED APS300 APS300R APS350 APS350A APS15KB APS40 APS25HJLA Programming Instructions: It is important to remember that during programming, each individual step of the procedure must be executed within 15 seconds of the previous step. When the 15 second time limit is allowed to expire, the system will automatically exit program mode. This is indicated by a long "chirp" from the siren. Additionally, any time the ignition key is turned off while programming, the system will immediately exit program mode. This is also indicated by a long "chirp" from the siren. To program additional transmitters: 1. Enter the vehicle, and turn the ignition key to the "on " position. 2. Flip the valet switch on - off - on - off - on - then off. 3. The dash LED will flash once, and the siren will "chirp" once, indicating the system is ready to accept programming for channel 1 or the arm/ disarm and panic functions. 4. You can assign any of the three transmitter button functions listed below to channel 1 a. Pressing button #1 on the keychain transmitter. b. Pressing button #2 on the keychain transmitter. c. Pressing both buttons simultaneously on the keychain transmitter. 5. Press and hold the selected choice a, b, or c above, until the siren emits a long "chirp" to confirm that programming of channel 1 was successful. 6. Move the valet/bypass switch on, then off again. 7. The dash mounted LED will flash 2 times, and the siren will "chirp" indicating that the system is ready to accept programming for channel 2, or the pulsed ground output for remote trunk release, remote car starter, etc. 8. You can assign any one of the two remaining button functions listed in 4a, 4b, or 4c above to operate channel 2. You cannot use the button(s) that operate channel 1, selected in step 5, to operate channel 2. 9. Press and hold the selected choice. The siren will emit a long "chirp" to confirm that programming of channel 2 was successful. 10. Move the valet/bypass switch on, then off again. 11. The dash mounted LED will flash 3 times, and the siren will "chirp" indicating that the system is ready to accept programming for channel 3. (APS 350) 12. Press and hold the remaining transmitter button function. The siren will emit a long "chirp" to confirm that programming of channel 3 was successful. 13. To exit program mode, either turn the ignition key to the off position, or move the valet switch on then off one additional time. This is indicated by one short chirp then one long "chirp" from the siren. NOTE: If programming to a Keyless Entry (non alarm) unit, there will be NO chirp indication. QUICK REFERENCE You can program any individual channel, without reprogramming all channels, by following the quick reference chart below. Channel Valet Switch LED 1 On then off 3 times 1 flash 2 On then off 4 times 2 flashes 3 On then off 5 times 3 flashes After the desired channel is programmed, turn the ignition key to the off position to exit programming mode. If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first. This remote needs to be programmed to your vehicle in order for it to work with your vehicle’s installed RKE (remote keyless entry) system: 1. PLEASE REFER TO YOUR ORIGINAL OWNER’S GUIDE FOR YOUR AFTERMARKET INSTALLED KEYLESS ENTRY SYSTEM OR 2. CONTACT A LOCAL CAR/AUDIO SHOP 3. CONTACT A LOCKSMITH 4. CONDUCT A GOOGLE SEARCH 5. CONTACT MANUFACTURER

Price: 22.46 USD

Location: Wellsboro, Pennsylvania

End Time: 2025-01-02T20:11:55.000Z

Shipping Cost: 6.96 USD