Big Dog Motorcycles PROGRAMMABLE Dyna 2000i Ignition Module ALL 2001-04 models

Description: New for Big Dog Motorcycles Dyna PROGRAMMABLE 2000i Ignition module to replace the legacy Thunderheart unit that is no longer available. This kit will move the ignition module into the nose cone, and the Dyna modules was stock on earlier Big Dogs. This kit also comes with a 4 PIN JST connector and necessary JST pins for direct plug and play for Big Dog 2003-2004 models, simply cut the wires once you re-route them to the desired length and match them up with the original harness. For the earlier models you can crimp or solder the connections.Please see our other replacement kit including a new Dyna Coil, Spark Plug Wires and JST connectors. Includes everything as pictured with Dyna standard instructions Fitment is for all Big Dog models 1994-2004. Dyna Products are Made in the USA! DYNA 2000i: The Dyna 2000i Programmable Ignition is the newest addition to the successful line of Dyna 2000 ignition systems. The 2000i not only adds to, but extends many features of the best selling Dyna 2000 module out of sight in a completely new design that fits under the cam cover. All 2000i ignition modules are PC programmable, putting you in control of your Harley’s performance.Featuring single fire operation down to 0 RPM for easier cranking and kicking, the Dyna 2000i will operate in all combinations of single fire or dual fire with single plug or dual plug heads (when used with appropriate coils).The Dyna 2000i’s built in tach driver delivers stable tach signal, even during rev limiting or can be used to activate shift lights, auto shifters, and other accessories.This module features data recording, keeping track of total engine hours, time at wide open throttle, number of engine starts (2 minutes running counts as one), longest time operating at wide open throttle, maximum RPM, seconds near rev limit and statistical analysis of time at RPM.Every time power to the ignition is switched on, the 2000i will check to see if the coil is shorted, mis-wired, or the wrong type. If an error is detected, the 2000i will immediately switch off and issue a warning by rapidly flashing the status indicator. Besides protecting the unit, this also prevents the costly failure of an improperly matched coil going bad one hour into your ride. After starting, the 2000i continuously monitors the coil and wiring status.With active dwell control, the module continually adjusts coil current to maintain maximum spark energy all the way to redline while eliminating coil stress caused by overcharging at idle. High efficiency design reduces battery draw for easier cold weather starting and lower charging system load.The Dyna 2000i was built to last — it cannot be damaged by broken or disconnected spark plug wires. The harness was constructed with TXL cross linked polyethylene automotive wire for exceptional resistance to abrasion, heat, and chemical attack. High temp glass braid jacket further increases the toughness of the harness and provides a tight, clean appearance. Wire colors closely match the factory harness for error free installation.FEATURESManufactured with premium quality components specifically qualified for operation in a high temperature / high vibration environmentProgrammable features include: part throttle curve, wide open throttle curve, rev limit, rear cylinder off set, dead cranking revs, security pin number, single/dual fire, retard mode8 advance curves to cover a broad range of engine builds and riding stylesRecords total engine hours, time at wide open throttle, number of engine starts (2 minutes running counts as one), longest time operating at wide open throttle, maximum RPM, seconds near rev limit and statistical analysis of time at RPM We have been selling Big Dog Motorcycle parts on ebay since 2003. We started as the original Big Dog factory liquidation outlet, then progressed to the exclusive contract buyer for all surplus parts from the factory including new overstock. When the company was foreclosed on in 2013, we purchased the remaining inventory and all of the original tooling from the bank. Since then, we have continued to manufacture new Big Dog Motorcycle parts with most of the original vendors using factory O.E.M. specs and materials. We have also upgraded some old parts and developed new parts in the manufacturing process. Check out my other items! Be sure to add me to your favorites list! International Buyers~ Global shipping – Please Note: Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying. Any questions- call Donna 6202572009

Price: 259.99 USD

Location: Lyons, Kansas

End Time: 2024-08-30T17:48:16.000Z

Shipping Cost: 0 USD