ESP32-C6 WiFi Bluetooth Development Board ESP32-C6-DevKitC-1 /ESP32-C6-WROOM-1

Description: ESP32-C6-DevKitC-1 Features:1. ESP32-C6-DevKitC-1 is an entry-level development board that uses the general-purpose module ESP32-C6-WROOM-1 with an 8 MB SPI flash.2. This development board has complete functions such as Wi Fi and low-power Bluetooth.3. ESP32-C6-WROOM-1 adopts an onboard PCB antenna, and the module is equipped with an ESP32-C6 chip, which has good functionality.4.The USB Type-C interface of the ESP32-C6 chip supports USB 2.0 full speed mode and can also be used as a power interface for development boards. It can burn firmware to the chip, communicate with the chip through the USB protocol, and can also be used for debugging.5. Most of the pins of the module on the board have been led out to the pins on both sides. Developers can easily connect various peripheral devices through jumpers according to actual needs, and can also plug the development board into the bread board for use. Parameter:Performance Introduction:ESP32-C6-WROOM-1 is a general-purpose module that supports 2.4 GHz Wi Fi 6, Bluetooth 5, and IEEE 802.15.4 (Zigbee 3.0 and Thread 1.3). The module is equipped with an ESP32-C6 chip and an 8 MB SPI flash. ESP32-C6-WROOM-1 uses an onboard PCB antenna,Pin Header: All available GPIO pins (except for the SPI bus in flash) have been led out to the pins on the development board.5 V to 3.3 V LDO: Power converter, input 5 V, output 3.3 V.3.3 V Power On LED: When the development board is connected to a USB power supply, this LED lights up.USB to UART Bridge: A single-chip USB to UART bridge that provides a transfer rate of up to 3 Mbps.ESP32-C6 USB Type-C Port: The USB Type-C interface of the ESP32-C6 chip, supporting USB 2.0 full speed mode and a maximum data transfer rate of 12 Mbps (note that this interface does not support high-speed transfer mode of 480 Mbps). This interface can be used as a power supply interface for development boards, can burn firmware to chips, can communicate with chips through USB protocol, and can also be used for JT-AG debugging.Boot Button: Download button. Press and hold the Boot key while pressing the Reset key to enter the "firmware download" mode, and download the firmware through the serial port.Reset Button: Reset button.USB Type-C to UART Port: can be used as a power interface for development boards, can burn firmware to chips, or as a communication interface to communicate with ESP32-C6 chips through an onboard USB to UART bridge.RGB LED: Addressing RGB light-emitting diode, driven by GPIO8.J5: Used to measure current.Size: 58mm * 25mmESP32-C6-DevKitC-1 power supply:1. Power supply from USB Type-C to UART interface or ESP32-C6 USB Type-C interface (choose one or both), default power supply method (recommended)2.5V and GND pin power supply3.3V3 and GND pin power supply Package include:1X development board2X pin arrangement (optional for welded/unwelded) Note:1. Please make sure to use a high-quality USB data cable. Some data cables can only be used for charging and cannot be used for data transmission and programming.When using 3V3 and GND pins to power the development board, it is necessary to remove the J5 jump cap and connect an ammeter in series to the external circuit in order to measure the current of the module. ESP32-C6-WROOM-1 Features:1.The ESP32-C6 development board is a development board launched by MuseLab based on the ESP32-C6-WROOM-1 module.2. It has an onboard USB to serial port and full-color RGB LED, making it convenient for developers to quickly conduct prototype verification and development.3. On board USB to serial port for more convenient operation.4. On board TYPE-C interface and full-color RGB LED onboard reset button, download button.5. With a wide range of applications, the low-power chip ESP32-C6 is specifically designed for IoT devices, including smart homes, industrial automation, consumer electronics, audio devices, and more. Product Introduction:ESP32-C6 is a system level chip (SoC) that supports 2.4 GHz Wi Fi 6, Bluetooth 5, Zigbee 3.0, and Thread 1.3. It integrates a high-performance RISC-V 32-bit processor and a low-power RISC-V 32-bit processor, Wi Fi, Bluetooth LE, 802.15.4 baseband and MAC, RF module, and peripherals. Wi Fi, Bluetooth, and 802.15.4 coexist and share the same antenna. Ultra low power SoC 2.4 GHz Wi Fi 6 (802.11 ax), Bluetooth with RISC-V 32-bit single core processor ® 5 (LE), Zigbee, and Thread (802.15.4) Flash can be selected up to 4 MB with 30 or 22 GPIOs, offering a wide range of peripherals. Parameter:Product Name: ESP32-C6 Development BoardModule model: ESP32-C6-WROOM-1Processor: Equipped with RISC-V 32-bit single core processorDownload interface: TYPE-CDevelopment environment: Windows, LinuxMain frequency: 160MHzSRAM: 512KBFLASH: 8MBProduct size: 5.3cm * 2.8cmThe application areas include:Smart HomeIndustrial automationConsumer electronics productsSmart agriculturePOS machineService robots• Audio devices• Universal low-power IoT sensor hub• Universal low-power IoT data logger Package include:1X development board2X15P pin arrangement (optional for welded/unwelded) On Oct 30, 2024 at 01:55:22 PDT, seller added the following information:

Price: 8.73 USD

Location: ShenZhen

End Time: 2024-11-30T09:49:42.000Z

Shipping Cost: 3 USD