Gecko GR214v Raptor Drive/Heatsink & Nema 34 1700oz 5a Motor & 26ft Motor Cable

Description: Please review the entire listing, and all videos as they cover all the details of this professional automation package.This package features Gecko's most advanced stepper drive, custom machined tool less mounted heatsink, Nema 34 1700oz/in stepper motor, and a 26ft.18awg 4 lead pre-built double shielded motor cable. This listing is for one drive, one heatsink, one motor, and one pre-built motor cable.The drive's specs are below, along with the heatsink,motor, and cable.Cooler Running Temperature: Upgraded, and over-rated power section components equal 30% reduction in heat compared to previous stepper drive revisions.Extra Resolution Choices: Ranging from half-step to 256-microstep resolution, a stepper can be run up to a resolution of 51,200 steps per revolution of your motors shaft. This is 25.6 times the resolution capability of a G540 drive!!Sub-Microstepping: At certain microstep resolutions the GR214V will automatically interpolate microsteps between rougher resolution choices. This means that the motor will move with the smoothness of a higher resolution option but will still have the lower input frequency requirement of the selected resolution. When operating in 2uStep, 4uStep and 8uStep modes the drive will interpolate to 16uStep motor smoothness. When operating at 5uStep the GR214V will interpolate to 10uStep smoothness. Higher levels of interpolation have significantly diminished returns, which is why this affects only lower resolution choices.Resonance Compensation: Using an entirely new method of motor control allows the GR214V to eliminate nearly all resonance. The two-tier system the drive uses eliminates resonance at the 1st and 2nd harmonic and at the midband, increasing torque and motor stability in unstable step motor regions.Full Step Morphing: Like all other Geckodrive stepper drives the GR214V has full step morphing. Between 3 – 6 RPS the drive will morph from microstepping to a true full step output to the motor, increasing high speed motor torque by 40% over a microstepping only driver. This requires no input from the user and the drive will not need any modifications in the software controlling it to take advantage of this.Soft Start: Step motors without a soft start drive operating them can draw significant inrush current. The GR214V ramps up current to the motor to avoid startup noise and premature tripping of protection circuitry due to sudden current loads.Spread Spectrum PWM: Most stepper controls have a fixed switching frequency which leads to motor harmonics and large EMI outputs. With spread spectrum PWM the GR214V switches randomly between switching frequencies at every step, eliminating harmonic knocking and EMI interference.Self-Test: A push button is used on the GR214V to allow for quick in-the-field testing of the drive’s core functionality. With a motor and power supply connected correctly the motor will turn at 1 RPS clockwise and counter-clockwise as long as the button is held down. This button input will take priority over all other input signals, meaning if STEP and DIRECTION are connected and the button is held down the GR214V will move in self-test mode.Protection Circuitry: The GR214V has rugged protection features to prevent damage in the majority of catastrophic events. It is protected against short-circuit, under-voltage, over-voltage, and over-temperature. The protection circuit will also detect an open motor phase and an unconnected motor. To clear a FAULT state the RESET input must be cycled to logic ‘0’ for one second and then returned to a floating or logic ‘1’ state.User adjustable standby current.If the onboard DIP switch is used to set phase current the user can adjust a trimpot for holding torque from 0% - 100% current in standby mode. If an external resistor or voltage is used the user may use a second resistor to set standby current, allowing full customization on multi-axis applications. After the GR214V has not received step pulses for one second it will enter standby mode, where it will limit current to a user-set percentage of maximum current. The GR214V will enter reduced-heating switching mode during this time to further decrease motor temperature during times of inactivity. My custom machined 6061 aluminum anodized heatsink in this package comes pre-mounted to the drive with thermal compound, and allows the end user the options of mounting the drive vertically, or horizontally to fit virtually any electronics enclosure. The heatsink also features tool less mounting with thumb nuts for ease of installation, and servicing all included with this DIY kit.The other included component is one of my Nema 34 1700oz 14mm single shaft (106.25in/lbs) stepper motors with 5a rating (7.5mh Inductance Rating). If your machine requires a large amount of torque this package will certainly get her automated. The motors full specs are below.Completing this CNC driver package is one 26Ft. 18AWG 4 lead Double Shielded Robotics Grade Motor Cabls pre-built with GX-16 5 pin female connectors soldered onto both ends. You can review the cable's listing here as well. https://www.ebay.com/itm/133300288430It also includes 1 GX-16 5 pin connector for your electronics enclosure "pass through" to allow the cable to plug into it, and 1 GX-16 5 pin Butt connector to attach to your motor's leads allowing your motor to plug into it on its end of the motor cable. This drive, motor, and cable package features a complete single axis assembly for your CNC system.This kit will save time, and money on sourcing, and building the correct motor cables for your CNC system. These are the only double shielded pre-built motor cables on the market.Please review the overview video below discussing the features of these drives, and cables included in this kit below. Gecko Raptor GR214V Drives (High Resolution Bullet Proof Drive) - YouTube Video will open in a new window Using the eBay App? Paste link into a browser window: [isdntekvideo]

Price: 390 USD

Location: Spring Hill, Florida

End Time: 2024-02-13T16:22:34.000Z

Shipping Cost: 0 USD