Lowering Blocks Kit Isuzu Rodeo 1976-2002 KB TF R7 R9 2" (50mm) 85x12mm U-bolts

Description: clearoutmyshednowclearoutmyshednowLowering Block Kit Isuzu Rodeo 1976-2002 KB TF R7 R9 2" (50mm)Kit Contains:2 Alloy Blocks Made of Billet 6063 AluminiumBlock Height 50 mm Block Width 58 mm, Block Length 110 mm4 of U Bolts : 85 x 12 mm8 of Serrated NutsTop Pin: 13 mmBottom Pin: 16 mmSome models may require 12mm Top Pin and 12mm Bottom Pin. PLEASE CHECK BEFORE ORDERING.Please measure your U-Bolts as well before ordering, as some models are 85 x 14mm or 75 x 12mm.2 -Year Replacement Warranty Important Information:Before you order, Please check your: Pin & U Bolt Size and compare to details above. And if this differs from the size you require, it is vital that you advise us what size you need, and we will send you the link for the correct kit. Please do not send a message us asking to change the kit. CHECK PIN AND U-BOLT SIZE. VARIATION POSSIBLE.Please ensure that you have the clearance to lower your vehicle by the height specified before purchasing. Check clearance as suspension parts may hit fuel tank when vehicle is lowered.Some vehicles may require drilling out of old mounting plates.Most kits have longer than standard U Bolts and will require cutting to size. (Refer to instructions stated below) INSTRUCTIONS FOR FITTING LOWERING BLOCKS 1. Jack the car up by the diff and fix axle stands under the front of spring hangers or chassis rails so that the wheels are at last 50mm clear of the ground. 2. Take the wheels off the car and undo the nuts that are at the bottom of the U-bolts. 3. Jack up the diff until the gap between the diff & spring pad is bigger than the height of the lowering blocks being fitted. 4. Check spring pads, top & bottom (if fitted to your vehicle). If they are worn, replace (Nolathane is highly recommended). 5. Now fit lowering blocks in place with recess hole fitting onto spring saddle rubber. Lower jack & square diff to springs. 6. Fit U-bolts over diff housing. Use G clamp if necessary & squeeze U-bolt to fit into holes in lower spring plate. If holes in lower spring plate are too small drill out to 12mm or 14mm depending on application. 7. U-bolts will form to the shape of the diff housing as you tighten up the nuts. 8. It may be necessary on some vehicles to cut excess thread length from the bottom of the U-bolt. This can be done by using a hacksaw. 9. Reverse jacking up procedure. 10. Recheck fitment of lowering blocs & re-tighten nuts after 1 week. 11. Lowering blocks fitment regulations vary from State to State. If doubtful of the requirements, contact your local Government transport office.Processing and PaymentWe know that buyers would want to receive their orders, as quickly as possible. All shipments will be posted using Australia Post, or one of our preferred couriers, within our handling time. We carefully pack all orders, to ensure that it reaches our buyers, in good condition. Buyers would need to provide us with a valid delivery address, and contact number, if there is a need to communicate about the transaction. We respond to all messages as quickly as we can, but in the event that the message was sent after hours, or possibly late in the day, during the weekend or on a public holiday, we will reply on the next business day. Accepted payment methods and all other information are available on our "Postage, returns & payments" area.Return PolicyWe offer a 30 day return policy for change of mind or incorrect purchase. Buyers can send it back and pay for return shipping cost, within 30 days from the delivery date, and has to provide a tracking number. All returned items for item cost refund must be in brand new, unused condition, in their original shipped packaging, sealed and unopened, and must include all parts and accessories. For any other issues or concerns, kindly send us a message so we could work things out.

Price: 84.95 AUD

Location: Campbellfield

End Time: 2024-12-22T09:33:00.000Z

Shipping Cost: 60.88 AUD