PRESTIGE Keyless car starter REMOTE Key FOB APS99BT3BCF4 ELVAT1C Green APS255C

Description: 800x600 Stock #: 532 A Shippers/relisters: 1) Stock 530, 530A, 531, 531A, 532 & 532A have interchangeable button pads This item is pre-owned – it will work like new once programmed to your vehicle One (1) Aftermarket remote keyless entry fob alarm Transmitter control clicker keyfob controller replacement Functions at 100% Tested & Guaranteed Audiovox / Prestige / Pursuit / Pro FCC ID: ELVAT1C Interchangeable FCC IDs: ELVAT1C ELVATOA ELVATIC ELVAT0A Part #: APS99BT3BCF4 circuit board # ATAE (green LED, not red) Frequency: 434 – 436 MHz LED color: Green 3 buttons Battery: (1) 23A Compatible with the following systems: Works on these Audiovox / Prestige / Pursuit systems: APS155CH, APS15CH, APS255C, APS255CH, APS25CH, APS25HT, APS410A, APS511C, APS610C, PRO9246CH, PRO9642CH, PRO9642CHWOS, PRO9644A and PRO9649A. APS155CH APS255C APS255CH Programming Instructions: PROGRAMMING TRANSMITTERS: It is important to remember that during programming, each individual step of the procedure must be executed within 15 seconds of the previous step. When the 15 second time limit is allowed to expire, the system will automatically exit program mode. This is indicated by a long "chirp" from the siren. Additionally, any time the ignition key is turned off while programming, the system will immediately exit program mode. This is also indicated by a long "chirp" from the siren. TO PROGRAM ADDITIONAL TRANSMITTERS: Note: The programming information described below assumes that the default transmitter is being used and the Lock/Unlock button is one and the same. If you have the optional transmitter with a separate Lock and Unlock button, use letter "B" reference below for programming. Also, where indicated that the siren will emit a long chirp tone, the optional horn may be connected, in which case either or both the horn and siren may sound. 1. (a) Enter the vehicle, and turn the ignition key to the "on" position. (b) Enter the vehicle, and turn the ignition key to the "on" position. 2. (a) Press and release the valet/bypass push button switch 3 times. (b) Press and release the valet/bypass push button switch 3 times. 3. (a) The dash LED will flash one time, and the siren will "chirp" 1 time indicating the system is ready to accept programming for channel 1, Arm/Disarm, Lock/Unlock and Panic. (b) The dash LED will flash one time, and the siren will "chirp" 1 time indicating the system is ready to accept programming for channel 1, Arm/Lock and Panic. 4. (a) You can assign the Lock/Unlock, Arm/Disarm button, by pressing and holding the lock/unlock button until the siren emits a long chirp tone. The chirp tone confirms that programming of channel 1 was successful. Up to 4 transmitters can be programmed, press and hold the selected button of each additional transmitter until the chirp tone is heard, or press and release the valet push-button switch two times to advance to step #8. (b) You can assign the Lock/Arm button by pressing and holding the lock button until the siren emits a long chirp tone. The chirp tone confirms that programming of channel 1 was successful. Up to 4 transmitters can be programmed, press and hold the selected button of each additional transmitter until the chirp tone is heard, or move to step #5 5. Press and release the valet/override switch one time to advance to channel 2. 6. (a) Disregard this step. (b) The dash mounted LED will flash 2 times, and the siren will "chirp" 2 times indicating that the system is ready to accept programming for channel 2. Unlock/2nd Unlock, Disarm, and Panic. Press and hold the Unlock button on your keychain transmitter until the siren emits a long chirp tone. This confirms that programming of channel 2 was successful. Up to 4 transmitters can be programmed, press and hold the selected button of each additional transmitter until the chirp tone is heard, or 7. Press and release the valet/override switch one time to advance to channel 3. 8. The dash mounted LED will flash 3 times, and the siren will "chirp" 3 times, indicating that the system is ready to accept programming for channel 3. Trunk Release Output, (where so equipped), or alternate channel output when used. 9. (a) Press and hold the 1st Opt. button on your keychain transmitter until the siren emits a long chirp tone. This confirms that programming of channel 3 was successful. Up to 4 transmitters can be programmed, press and hold the selected button of each additional transmitter until the chirp tone is heard. (b) Press and hold the Opt. button on your keychain transmitter until the siren emits a long chirp tone. This confirms that programming of channel 3 was successful. Up to 4 transmitters can be programmed, press and hold the selected button of each additional transmitter until the chirp tone is heard. 10. Press and release the valet/override switch one time to advance to channel 4 if so equipped. If your system does not have a 4th channel, a long chirp followed by a short chirp tone will indicate that the program mode has been exited. 11. The dash mounted LED will flash 4 times, and siren will "chirp" 4 times indicating that the system is ready to accept programming of channel 4. 12. (a) Press and hold the remaining Opt. button of the transmitter until the siren emits a long chirp tone. This confirms that programming of channel 4 was successful. Up to 4 transmitters can be programmed, press and hold the selected button of each additional transmitter until the chirp tone is heard. (b) Press and hold any combination of two buttons simultaneously, until the siren emits a long chirp tone. This confirms that programming of channel 4 was successful. Up to 4 transmitters can be programmed, press and hold the selected button of each additional transmitter until the chirp tone is heard, or press and release the push button switch to exit the programming mode, or turn the ignition switch off to exit the programming mode. The siren emits a long followed by a short chirp tone indicating that the program mode has been exited. NOTE: If programming to a Keyless Entry (non alarm) unit, there will be NO chirp indication. QUICK REFERENCE You can program any individual channel, without reprogramming all channels, by following the quick reference chart below. (Not All Units Have 4 Channels) CHANNEL VALET SWITCH LED 1 Press and Release 3 Times 1 Flash 2 Press and Release 4 Times 2 Flashes 3 Press and Release 5 Times 3 Flashes 4 Press and Release 6 Times 4 Flashes After the desired channel is programmed, turn the ignition key to the off position to exit programming mode. STOP! Before You Buy Please Read… Program Remote To Your Vehicle If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first. This remote needs to be programmed to your vehicle in order for it to work with your vehicle’s installed RKE (remote keyless entry ) system: 1. PLEASE REFER TO YOUR ORIGINAL OWNER’S GUIDE FOR YOUR AFTERMARKET INSTALLED KEYLESS ENTRY SYSTEM OR 2. CONTACT A LOCAL CAR/AUDIO SHOP 3. CONTACT A LOCKSMITH 4. CONDUCT A GOOGLE SEARCH 5. CONTACT MANUFACTURER Payment: We accept payment via PayPal or Credit Card. Please contact us via eBay messages for any questions concerning payments. Payment is expected within 5 days. PA SALES TAX: As per the State of PA Franchise Board we must collect sales tax from PA Residents for any purchase made from our store. Contact/Email: Due to scams etc, we DO NOT respond to emails. We only read/respond to EBAY MESSAGES. Messages & Best Offers are checked throughout the day & we typically respond 7 days a week. Please contact us with questions via eBay messages (keyless4u). 100% Guarantee Remote Shipping / Return Policy Shipping & Handling Combined Shipping & Handling Discount (multiple item purchase discount): S&H discount = the price of the 1ST remote’s S&H + 1.99 each additional remote’s S&H Shipped From: Pennsylvania, USA Shipping Method: USPS mail service USA Shipment Options: ◊ USPS 1ST class mail service ◊ USPS Priority class mail service ◊ USPS EXPRESS class mail service Canadian Shipment Options: ◊ USPS 1ST class mail service ◊ USPS Priority class mail service ◊ USPS Express class mail service Worldwide (Outside of USA & Canada) Shipment Options: ◊ USPS Priority class mail service ◊ USPS Express class mail service Warranty/Returns: 1. We have a 30 day return policy. 2. All returns for replacements and refund need an RMA #. 3. Please contact us before returning items so we can give you the RMA # and the proper return address. 4. No refunds / replacements will be granted without an RMA# We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Each button is tested for functionality prior to shipment and then logged. Please Note: Each remote and circuit board is UV id’d prior to shipment – All returns receive a UV ID inspection to verify originality of remote sent prior to refund or replacement. Does this keyless remote entry come with a battery? Yes. It will have a working battery installed. Battery Condition: A. All remotes sold on Keyless4u include working batteries. B. Installed batteries are not tested for battery life- they are simply working. Some are new and some are used. Your vehicle will be installed with one of the following keyless entry systems: a. Standard Keyless Remote Packages: Installed at time of manufacture. b. Optional Keyless Remote Packages: Installed by a dealer. c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop. d. No remote keyless entry system at all. The above information can change which remote you need for your installed remote keyless system. Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4

Price: 17.99 USD

Location: Wellsboro, Pennsylvania

End Time: 2025-01-04T15:04:15.000Z

Shipping Cost: 6.96 USD